SN Pixel operation Manual

One Button Lightsaber Instructions:

1. Power on and off (make sure the sword is charged first):

  • To ignite the sword, hold the button down until it glows and then click it once, or quickly turn the sword's hilt left and then right.
  • To retract the sword, hold the button for 4 seconds or quickly turn the sword's hilt from left to right again.

2. Key instructions when the sword is not ignited:

  • Change Blade Color: Press the button and rotate the sword's hilt to change the blade color.
  • Adjust volume: Press and hold the button for 1 second.
  • Change ignition effect: Press and hold the button for 2 seconds.
  • Change Blade Effects: Press and hold the button for 3 seconds.
  • Change soundfonts: Press and hold the button for 4 seconds.
  • Power Save Mode: The sword will go into power save mode after 20 minutes of inactivity.
  • The sword will beep when the batteries are properly installed.

3. Key instructions when the sword is ignited

  • Blaster Effect: Click the button once.
  • Sword Lock: Press and hold the button for 1 second, then release.
  • Change blade color: Press and hold the button for 2 seconds, then release.
  • Flash On Clash: Hold the button for 3 seconds and then release to turn the effect on or off.
  • Retracting the bar: press and hold the button for 4 seconds or turn the handle of the bar.

4. Movement based effects when the sword is not ignited

  • Change Soundfonts: Point the blade up, hold the button, then rotate the sword.
  • Change background music: Point the blade down, hold the button and then rotate the sword.

5. Movement based effects when the sword is ignited

  • Change Blade Color: Point the sword down, hold the button, and then rotate the sword.
  • Flash On Clash: The sword will flash and make a sound when it hits a surface.
  • Drag Effect: Hold down the button and then hit with the sword.
  • Tip melting effect: Hold the button and then thrust the sword.
  • Power Effect: Point the sword up, hold the button and rotate the sword.

Two Button Lightsaber Instructions:


1. Power on and off (make sure the sword is charging first):

  • To ignite the sword , click the top button or turn the sword's hilt.
  • To retract the sword , click the top button or rotate the sword's hilt.

2. Key instructions when the sword is not ignited

  • Change the soundfonts : Click the bottom button once
  • Adjust the volume: Click both buttons at the same time to enter volume control mode. Then click the top button to increase the volume or the bottom button to decrease the volume.
  • Change ignition effect: Press the top button for 0.5 seconds.
  • Change blade effects: Press and hold the bottom button for 0.5 seconds (the knife effect will be announced).
  • Power saving mode : The sword will go into power saving mode if it has not been used for 20 minutes.
  • The sword will beep when the batteries are properly installed.

3. Key instructions when the sword is ignited

  • Blaster Effect: Click the bottom button.
  • Saber Lock Effect: Press the bottom button for 0.5 seconds.
  • Lightning Strike effect: Click both buttons at the same time to turn the effect on or off.

4. Movement based effects when the sword is not ignited

  • Switch soundfonts: Point the sword up, hold the bottom button and then rotate the sword.
  • Change background music: Point the sword down, hold the bottom button and then rotate the sword.

5. Movement based effects when the sword is ignited

  • Change Blade Color: Point the sword down, hold the bottom button, and then rotate the sword.
  • Flash on Clash: The sword flashes and makes a sound when it hits a surface.
  • Drag Effect: Hold the top button, then strike with the sword.
  • Melting Effect: Hold the bottom button, then thrust the sword in.
  • Power Effect: Point the sword up, hold the bottom button, then rotate the sword.


Please contact info@sabersforce.com if you have any questions.